PROJECT SHOWCASE
We want to showcase your projects. It is inspirational to see what others have made. We can all learn from each other. In addition to posting your project we ask you to provide additional information: The type(s) of wood used, finish, and some details about your project.
Click this link to submit a project for the showcase
Date submitted: 03/11/2022
Submitted by: Len Coleman
Project: Beer tap handles
Wood(s) used: Various
Finishes used: CA Glue
Comments: My nephew is opening a brewery. In honor of his father who was a drummer, he is naming the brewery Encore. He asked me to turn beer tap handles in the shape of drumsticks. These are the finished products I gave him.
Date submitted: 03/25/2021
Submitted by: Lynn Southward
Project: Butterfly
Wood(s) used: Basswood and Maple
Finishes used: Acrylic Paint
Comments: I turned the body for this butterfly on my 3520a lathe. It’s probably the smallest thing I have turned on it.
Date submitted: 03/24/2021
Submitted by: Len Coleman
Project: Small Bowl
Wood(s) used: Spalted Maple
Finishes used: Wipe on Polyurethane
Comments: I improved my turning enough that the sanding became easier. Also improved my sanding techniques
Date submitted: 03/24/2021
Submitted by: Len Coleman
Project: Small Bowl
Wood(s) used: Cherry
Finishes used: Wipe on Polyurethane
Comments: I improved my turning enough that the sanding became easier. Also improved my sanding techniques
Date submitted: 03/24/2021
Submitted by: Len Coleman
Project: Goblet
Wood(s) used: Cherry
Finishes used: Wipe on Polyurethane
Comments: As I started turning, I found several cracks inside the wood. I modified (shortened) the goblet to eliminate the worst cracks. I put CA glue on the remaining cracks and so far it is holding)
Date submitted: 03/15/2021
Submitted by: Jim Nickless
Project: Cremation Urns
Wood(s) used: Walnut, Maple, and Bloodwood
Finishes used: Epoxy inside, Shellac outside (Urethane will be sprayed on when warmer weather comes)
Comments: I made these Urns for the very distant future, (We hope). They are about 12 inches tall with a diameter of about 6 inches. They have a capacity of 200 cubic inches each, (My research said one cubic inch per pound). Each Urn has 246 pieces.
Date submitted: 02/17/2021
Submitted by: Das Madhavan
Project: Wave form cutting jig
Wood(s) used: Plywood
Finishes used: none
Comments: I wanted to cut an arc on the bandsaw that is ready to laminate and glue without any sanding. Sanding changes the shape slightly so the two halves won’t keep the inlay perfectly seated. Freehand sawing is always prone to have slight bumps (at least for me). So this jig which uses a chuck to hold the work piece and a circle cutting fixture as a base will give you a perfectly cut arc on any work piece mounted on the chuck. If anyone wants more pictures and description, please let me know.
Date submitted: 02/08/2021
Submitted by: Joseph H Wise
Project: Weed Pot
Wood(s) used: Sycamore
Finishes used: Lacquer, Chestnut Stains, and wax
Comments: This was actually a multi-axis turning, though it is hard to tell. Once I turned the wood round, there was a flat spot which I left.
Date submitted: 02/06/2021
Submitted by: Das Madhavan
Project: Clamshell tower lidded box
Wood(s) used: Red Cedar & Walnut
Finishes used: Mylands friction polish
Comments: My former club *(still a member CAT) had a challenge to make one of these signature project of Cindy. She makes one with 8 lobes. As I was cutting, I made a mistake in my angle calculation and wound up with 12 lobes. My wood was not exactly dry either. So, the lid warped a little bit, but still stays put. Now, if you think cutting the rim shape is a piece of cake, try one. It took me a whole week fiddling around to get it correct. I want to see how Cindy does it. Am sure, her method is more refined.
Date submitted: 02/06/2021
Submitted by: Das Madhavan
Project: Wine goblet in Aromatic cedar
Wood(s) used: Aromatic cedar
Finishes used: Mylands friction polish
Comments: The last time I attended, Lynn’s demo was to make the stem for the wine goblet glass top. The president’s challenge was to make one. I had plenty of wood but no glass upper portion of the goblet. I was in a cheap mood to go and buy one. Besides, didn’t know where to go locally. So, made couple in total wood. This is one of them
Date submitted: 02/06/2021
Submitted by: Das Madhavan
Project: Wave form with 3 layer inlay
Wood(s) used: Red cedar, yellow heart, blue veneer
Finishes used: Mylands friction polish
Comments: The yellow heart is a tough inlay material as it won’t bend and stay. I had to really steam the heck out of it until it nearly cooked through. My mistake was to cut it to 1/8″ thick. Next time, I will stay with 1/16″ After hollowing out most of it, I think it will stay put now.
Date submitted: 02/06/2021
Submitted by: Das Madhavan
Project: Celtic knots on lidded boxes
Wood(s) used: Cherry, Black Walnut, Spalted Box Elder, Spalted Cherry
Finishes used: Mylands friction polish
Comments: vThese are Celtic Knots on various forms and woods. I had to design a jig to give me predictable intersections of the knots. Takes too much time, but the results are great. Must have everything centered without any deviation! The same jig allows me to cut the work piece in arcs too.
Date submitted: 02/06/2021
Submitted by: Das Madhavan
Project: Double Sine Wave form on a tower lidded box
Wood(s) used: Cherry, mahogany,purpleheart
Finishes used: Mylands friction polish
Comments: I built some simple Sine Wave pattern inlays on many forms. Thought I will try a double Sine Wave. Kind of pretty?
Date submitted: 01/31/2021
Submitted by: Lynn Southward
Project: Carved Bowl
Wood(s) used: Boxelder
Finishes used: Lacquer
Comments: I wanted to combine carving and turning
Date submitted: 01/31/2021
Submitted by: Lynn Southward
Project: Violin
Wood(s) used: Maple and Spruce
Finishes used: Violin Finish
Comments: I bought a book 35 years ago and just decided to get it done
Submitted by: Lynn Southward
Date submitted: 01/31/2021
Project: Urn
Wood(s) used: Maple Burl
Finishes used: Lacquer
Comments: I made it for a friend